Is the buttons on clasp on bracelets loose on your pieces, mine woggles quite a bit and wish it didn't. Also, the inner side of clasp is quite sharp, compared to smooth one I got on 42mm VSF PO 8500.
-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
Vsf 2018 seamaster diver 300m
- Thread starter GENneral
- Start date
cannockwolf
Known Member
chentepilot
Known Member
- 7/11/18
- 163
- 132
- 43
Enthusiast88
Known Member
Here she is boys! Photos were taken indoors, I’ll take better photos with better natural lighting tomorrow.
- 26/12/13
- 4,613
- 3,075
- 113
Lovely! Now I need to get the blue one too... Damn you all to hell 
Enthusiast88
Known Member
Lovely! Now I need to get the blue one too... Damn you all to hell
Thanks bro, she’s gorgeous:inlove: might pick up on the black one later on. These things are pretty much gen!
Vince Ong
Do not accept unsolicited offers
- 11/4/19
- 14
- 2
- 3
Same, the bracelet on mine rattles quite a bit. Especially the push button for the extension. If it gets broken I think I'll just glue it up with some epoxy haha.
Last edited:
Vince Ong
Do not accept unsolicited offers
- 11/4/19
- 14
- 2
- 3
Lovely! Now I need to get the blue one too... Damn you all to hell
Except for the movement.. hahah
Enthusiast88
Known Member
Enthusiast88
Known Member
Yup nothing bad about it, mine is running less than 2 seconds a day. I love it and the decoration looks very very close to gen.
Enthusiast88
Known Member
Merlinski
Getting To Know The Place
The same here :-( When I push the crown back after setting the time it doesn't go to the position to wind but stays in the position to change the date. That's very annoying because when I then try to screw the crown in the date changes. I need to press strongly after setting the time and at the same time screwing in.
Mine arrived too! One think struck me a bit. Usually I don't have any problems distinguish between crown positions but with this it's problematic... Does anyone encounter similar problems? Thank you!
I hope you guys understand what I mean because of my poor English ...
Gesendet von meinem HUAWEI CAN-L11 mit Tapatalk
I got my grey dial last week. I just want to give a little feed back.
1. 3 and 9 markers are misaligned.
2. Pearl is sharp with bad finish and can cut your fingers. I used the back of old belt to rub it and it solved the problem without scratches.
3. My bezel can turn backward a little bit. It is not GMT(lol).
4. I feel the rubber is too soft but some friend here say it is supposed to be soft as the gen is also soft.
over all I think it worth the money.
I like it
1. 3 and 9 markers are misaligned.
2. Pearl is sharp with bad finish and can cut your fingers. I used the back of old belt to rub it and it solved the problem without scratches.
3. My bezel can turn backward a little bit. It is not GMT(lol).
4. I feel the rubber is too soft but some friend here say it is supposed to be soft as the gen is also soft.
over all I think it worth the money.
I like it
That is an easy fix for anyone that has done any work on watches at all. All you have to do is shorten the crown stem maybe 1mm or something and reassemble. I can see why you would be annoyed, but that is part of the fun with reps, right?
No idea, but I just took a pic of mine. It isn't that easy to photograph, but assuming you are referring to the number on the back of the lug @ 1 mine is 89236388
