-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
Nautilus date wheel project
- Thread starter Keylog74
- Start date
AgentPena
Active Member
I'm excited about this project, have not come across any DW modders that does for 9015. I heard it's costly to develop for this movement hence even Mikey himself is not involve.
looking forward to it. I would pay $100 for a good DW. Just make sure each numerals align in the centre of the DW window.
best of luck!
looking forward to it. I would pay $100 for a good DW. Just make sure each numerals align in the centre of the DW window.
best of luck!
date overlays will be cheaper and easier to make. they do not need to make a new 9015 date disc. with the mikey and legend project they need to buy or manufacture the date disc.
agree get the numbers aligned properly and will sell loads
- 14/6/13
- 3,849
- 1,686
- 113
Well just a quick update. Ive shipped out two Pateks to be disassembled and start measurements 
Well just a quick update. Ive shipped out two Pateks to be disassembled and start measurements
Great wonderful superb news!
AgentPena
Active Member
I have not thought about dw overlays. Great idea indeed without it being costly! Does this mean we have ti disassemble our 9015 and send it to them to paste over?
Thank you
go back to post #1 and you can see the pateks use a overlay. the aquanaut and nautilus date window is further right than regular 9015 ring.
my best guess would be spongebob makes a new overlay rings then your modder has to manage the alignment during fitting
the miyota date wheel sits below the overlay which is held with glue
AgentPena
Active Member
go back to post #1 and you can see the pateks use a overlay. the aquanaut and nautilus date window is further right than regular 9015 ring.
my best guess would be spongebob makes a new overlay rings then your modder has to manage the alignment during fitting
the miyota date wheel sits below the overlay which is held with glue
Thanks for the clarification, much appreciated
BIONONE
Respected Member
- 28/4/17
- 3,624
- 2,815
- 113
Will upload the new Date Wheel Vector this weekend as i had too much stuff to do so far.
Next thing i need to know is the measurement for the overlay itself and the DW cut out to align every number perfectly.
Keylog74 Let me know when Steve send you the information so i can go on.
Thanks
Next thing i need to know is the measurement for the overlay itself and the DW cut out to align every number perfectly.
Keylog74 Let me know when Steve send you the information so i can go on.
Thanks
Last edited:
BIONONE
Respected Member
- 28/4/17
- 3,624
- 2,815
- 113
a nice icing on the cake would be to get a high resolution scan of the old faulty PF overlay to work around it.
Once it is disassembled i think it is not that o a big deal to scan it for a better work performance of mine
Once it is disassembled i think it is not that o a big deal to scan it for a better work performance of mine
- 3/6/14
- 14,533
- 5,765
- 113
BIONONE
Respected Member
- 28/4/17
- 3,624
- 2,815
- 113
Not prof on this.
My bad - thought i read something about Prof.
edited it
anyways - every measurement is welcome.
- 14/6/13
- 3,849
- 1,686
- 113
My bad - thought i read something about Prof.
edited it
anyways - every measurement is welcome.
Spongebob is taking on the project
both watches are already with him. Last time I spoke to him I was told to wait for Thursday. I did however just asked him if he can do the scan needed. Just wait for him to reply.
