DonkeyHoTay
Cockwomble Misfire Specialist
This thread is making me want a plain jubilee clean v3 Pepsi. But should I get the deep crystal for it…
-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
Clean GMT-II Pepsi updated bezel insert V2/V2s review and comparison
- Thread starter CTime
- Start date
DonkeyHoTay
Cockwomble Misfire Specialist
interesting! I just got delivery of a clean 126500LN Panda and a VSF 126506 Platona with extra weight….. same box and no problems with shipping. Fingers crossed on my GMT meteorite re-do.
DonkeyHoTay
Cockwomble Misfire Specialist
If you mean pictures of the Clean Pepsi v3 franken with the Meteorite dial, I will send when I get QC from TD.
Unfortunately I had to RL the QC the first time around because of what looked like scratches on the bezel and/or rehaut - maybe installation mishap during dial and crystal upgrades:
TD made it right with part replacements, but it all went to shit when the package got stuck in Malaysia. Hoping that round 2 works out!
- 29/8/20
- 627
- 592
- 93
that I prefer because I'm 51 and on the rep I can read the date without glasses and it makes me feel younger LOL
why the F cant they fix the DW mag? Its been released for so long. What's the issue here simply the gasket size? I dont get it how hard it is to rectify this.
I wonder, if they change the gasket size to lower the crystal (and thus, the magnification), does the crystal protrusion now not match gen? Or, is it closer to gen?
Then the crystal hits the second hand.
So for them to fix the issue once and for all, they would need to fix the gasket and the height of the second hand
- 25/3/17
- 4,465
- 4,006
- 113
The gen case has a lower flange than the CF one, the gasket supplied with the gen crystal is 2.2 mm high. These gen crystal + gen gasket measurements are produced by Rolex to have the right glass height (a little protruding from the bezel) and the correct date magnification. I just assembled it including the gen case. As you can see the dial in the gen is less sunken. The gen hands do not touch the glass in this case but it must be said that my 3285 movement comes from a CF V1 (in the first series there was no problem with the hands touching the glass). This is the result with all gen parts (except movement):
I had 3 different CF v1, 2 of them touched the glass, 1 didn’tThe gen case has a lower flange than the CF one, the gasket supplied with the gen crystal is 2.2 mm high. These gen crystal + gen gasket measurements are produced by Rolex to have the right glass height (a little protruding from the bezel) and the correct date magnification. I just assembled it including the gen case. As you can see the dial in the gen is less sunken. The gen hands do not touch the glass in this case but it must be said that my 3285 movement comes from a CF V1 (in the first series there was no problem with the hands touching the glass). This is the result with all gen parts (except movement):
It just luck of the draw sometimes
- 25/3/17
- 4,465
- 4,006
- 113
Yes broI had 3 different CF v1, 2 of them touched the glass, 1 didn’t
Fusible
Renowned Member
- 5/5/22
- 638
- 1,063
- 93
Correct! Shaving the seconds hand generally works but yes it’s annoying to immediately send a new watch to the modder. For these reasons I prefer to go with C+ as they have a better hand stack height without the DD movement.
DonkeyHoTay
Cockwomble Misfire Specialist
This thread is making me want a plain jubilee clean v3 Pepsi. But should I get the deep crystal for it…
Ordered it from my favorite TD... keeping the clean crystal on it - trusting the views on this thread that there is no need for a deep crystal upgrade and that OOTB it's good to go!