-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
BBR factory RM 055
- Thread starter j21
- Start date
ahh, i asked for the screwdriver and strap as well, but only for the screwdriver he asked 20£ which is a bit too much, i ll get the strap with the box with another order and i ll do some research for the screwdriver tbh
Just approved my qc!! Could you pls share where you got the ARx3 crystal?V2 carbon under natural sunlight
I was looking at this and I red it’s not possible to actually apply the coats DIY, it must be done with industrial equipment which means need to buy the crystal itself.
RWI's go to for 2xAR is https://forum.replica-watch.info/forums/profs-crystals.301/. Read the T&C's but I'm pretty sure you'll either need to send the watch or at least the crystal to prof to apply the coating.
Hi Guys,
i also got my QCs (usally i check especially the dial alignments, so i am not really sure what to look out for here...) but my timegrapher results are a little odd -
amplitude is 344, is this normal with this movement?
i also got my QCs (usally i check especially the dial alignments, so i am not really sure what to look out for here...) but my timegrapher results are a little odd -
amplitude is 344, is this normal with this movement?
I believe you got the answer under your post on reptime qc, it was due to the watch being fully winded, you are fine. For a second I was concerned about your crown (assuming it is meant to be black, same model as mine) but then I realised you choose a different model - red font silver crown- so makes sense
Well, i am still not 100% convinced, since all watches should be fully wound before testing... so compared to your 311, my 344 is still pretty high.
But it seems no big deal to anybody and there is no way to make sure TDs fully wind it before testing anyway, so its ok!
Ah, thats a great info about the crown, TD mentioned its different than the others, but i couldnt figure it out.
Thank you!
But it seems no big deal to anybody and there is no way to make sure TDs fully wind it before testing anyway, so its ok!
Ah, thats a great info about the crown, TD mentioned its different than the others, but i couldnt figure it out.
Thank you!
- 25/9/22
- 6,017
- 16,371
- 113
Anything above 310 is not great since it is a sign of overbanking. No comments about the movement since I'm not familar with it.
Guys just got mine, it is damaged at the top left corner, the NTPT is scratched clearly from overpressure. What do I do? andiot is not really willing to help, he says there is no evidence that it was scratched after QC
- 25/9/22
- 6,017
- 16,371
- 113
Have one on the way
Overall, case shape for the NTPT is worse than the previous versions, the rehaut is too thick, you can compare with gen to see
But the movement which is 80% of the watch is fantastic
Rest of the watch is typical BBR, shitty strap and clasp
- 25/9/22
- 6,017
- 16,371
- 113
- 25/9/22
- 6,017
- 16,371
- 113
ZF RM55, new super clone movement
ZF will release the new RM55 with new super clone movement, it's almost the same as genuine movement. 95% same as genuine. You may have seen this movement before, but the price is insane. The previous price was about $20k, but after ZF mass production this time, the price will be reduced to...
forum.replica-watch.info
Is this the true clone Vaucher? Or is it the new BBR v3?
- 25/9/22
- 6,017
- 16,371
- 113
Disregard. Close inspection tells me its not the BBR v3 movement for sure.ZF RM55, new super clone movement
ZF will release the new RM55 with new super clone movement, it's almost the same as genuine movement. 95% same as genuine. You may have seen this movement before, but the price is insane. The previous price was about $20k, but after ZF mass production this time, the price will be reduced to...
Is this the true clone Vaucher? Or is it the new BBR v3?
Just an informative post from my last update, i unscrewed the case and it came out smoothly, it s not glued, so build as gen. Seller is sending me a new one so i ll swap it soon.
Just quiet because nothing is happening atm, expected tbh until ZF drops the new version or the are news about the vaucher movementI think the thread is now dead
Update: new ntpt bezel received from Andiot. Glad this is sorted. Swap was easy, just be very very carful if you are ever unscrewing the bezel, these screws scratch very easily, do not apply too much torque. Pics below:
