ZF Master Ultrathin Moon

[Bassy2000]

Watch is at the Watchmaker now, he received it today...we will see...hope only a service or nothing serious

Thank you for the update! Hope you have it back soon fully functional.

 

[freediver]

That thing with the damaged screws and water resistant are holding me back. I hope they are sorted soon

 

[jrodshibuya]

Is everyone accepting the models with damaged screws. I spoke to my TD and he said it's in stock but they all have screw problems

I accepted with QC pics that may have a slightly damaged screw or two. See here:

 

[KJ2020]

Is everyone accepting the models with damaged screws. I spoke to my TD and he said it's in stock but they all have screw problems

I would not, that's unacceptable. Maybe they'll quit sending them out that way if they keep getting them sent back.

Rep or not, it's a $400 watch.

 

[vcappp]

Got my watch Smith to shorten the stem. Now the crown sits flush to the case. Sort of straightened the date hand as well but due to the uneven intervals between the dates, some of the dates will still not be centered.

Some things to look out for in QC pics.

Sent from my ONEPLUS A6003 using Tapatalk

what was the reason of the problem that the date hand is not centered (not properly pointing the date)? which looks like the date hand is one tick off

was the local watchsmith friendly with the rep?


Sent from my iPhone using Tapatalk

 

[Xander22]

The spacing between the dates (1 . 3 . 5...) are probably not evenly spread out. Either that or the intervals in which the date hand moves each day is not equal. So there will be some days when the date is lined up perfectly and some days when the date is slightly off. Hope my explaination makes sense. Maybe the others who have the same watch can advice.

Yes. He is rep friendly. He sells lower end reps as well. Haha.

Sent from my ONEPLUS A6003 using Tapatalk

 

[VIV54]

My watch was sent back from Lucy to the factory since she realized it had some dust on the dial. I hope they don't damage the screws, I told her they are butchers. I'd prefer 1000 times a bit of dust than damaged screws.

 

[Xander22]

My watch was sent back from Lucy to the factory since she realized it had some dust on the dial. I hope they don't damage the screws, I told her they are butchers. I'd prefer 1000 times a bit of dust than damaged screws.

I think the issue with the screws is that it's not standard size. My watchsmith had some difficulty getting the screws back in yesterday. Was switching between different screwdrivers.

Sent from my ONEPLUS A6003 using Tapatalk

 

[VIV54]

I think the issue with the screws is that it's not standard size. My watchsmith had some difficulty getting the screws back in yesterday. Was switching between different screwdrivers.

Sent from my ONEPLUS A6003 using Tapatalk

I owned an ultra thin date from another factory and I opened it with ease many times. But it's obviously a screwdriver problem not fitting properly in the screw and damaging it while turning. I will never understand why they are so good at replicating crazy stuff and then they fall on these stupid things.

 

[RobSe1]

I owned an ultra thin date from another factory and I opened it with ease many times. But it's obviously a screwdriver problem not fitting properly in the screw and damaging it while turning. I will never understand why they are so good at replicating crazy stuff and then they fall on these stupid things.

This!! They make watches with 904L steel and putting shitty bracelet screws in ... cannot get this, too.

 

[jrodshibuya]

Hard to see but the screws in this gen look pretty dirty and rough:

 

[AriChoresh]

came out yet? looks amazing imo

 

[timnic54]

Once screws have been opened they really should be replaced when re-fitting. But not even JLC do that in fact.

This is my gen JLC MUT after a service with JLC

I think it is not a big deal only shows up in macro photos. Better that they have fixed the WR issues.

 

[AriChoresh]

Once screws have been opened they really should be replaced when re-fitting. But not even JLC do that in fact.

This is my gen JLC MUT after a service with JLC

I think it is not a big deal only shows up in macro photos. Better that they have fixed the WR issues.

Amazing

 

[vcappp]

The spacing between the dates (1 . 3 . 5...) are probably not evenly spread out. Either that or the intervals in which the date hand moves each day is not equal. So there will be some days when the date is lined up perfectly and some days when the date is slightly off. Hope my explaination makes sense. Maybe the others who have the same watch can advice.

Yes. He is rep friendly. He sells lower end reps as well. Haha.

Sent from my ONEPLUS A6003 using Tapatalk

Thanks for your reply. Was the date hand mis-alignment problem easy to fix by the watch-smith?


Sent from my iPhone using Tapatalk

 

[christo14]

Once screws have been opened they really should be replaced when re-fitting. But not even JLC do that in fact.
This is my gen JLC MUT after a service with JLC

I think it is not a big deal only shows up in macro photos. Better that they have fixed the WR issues.

That movement looks amazing!!

 

[Xander22]

It's easy to pull the hand out and align it to a number. But like I said. It may be aligned to some numbers but may not be aligned to others. Maybe if you're lucky you won't have this problem on your watch.

Sent from my ONEPLUS A6003 using Tapatalk

 

[deglingo70]

deglingo70 I would also like to know what was your problem with the moonphase and if you fixed it!

Keep us updated

Hello VIV54
I returned the watch to the seller, I wait for news

 

[qualityazn]

damn i didn’t see the date misalignment until now. now i cannot unsee it

 

[B0j]

Anyone receive one in RG yet? Preordering RG black dial and wanted to see if anyone has gotten their’s yet.