"Official DSSD Club"

[willisd]

Thanks for the reply

Im from Australia and new to the forum and sorry for the question but is it usually a case of buying a watch and sending it to one of the members on the forum to have it done?

 

[zdra]

There's an interesting page

http://www.bernardwatch.com/blog/ro...-116660-fake-vs-real-comparison/#comment-2313

 

[zdra]

Just joined the club, I got this from Sead yesterday. Noob ultimate, asian 2836.

Sent from my LG-D802 using Tapatalk

 

[zdra]

Clasp

Sent from my LG-D802 using Tapatalk

 

[zdra]

And the problem on the very first day:

The pin holes are too shallow and without sharp edges, so this will keep coming off the pin. Any idea how to address this?

Sent from my LG-D802 using Tapatalk

 

[OPdestrolover]

Has someone had the possibility to compare weight of gen DSSD to Noob 2014 version ?
We're looking for so many cosmetic differences, but how about a very obvious one, the weight ?

 

[OPdestrolover]

This is a BK DSSD with Swiss ETA movement.

 

[Ata197]

Great intro to DSSD

 

[Snoweagle]

Here's my Noob DSSD V1.

 

[nicosuave4201]

I have a problem with my deep sea. I've had the watch a month now and am just now noticing this.

In the bottom right quadrant of the watch face area, the bezel has a downward flex to it. As in, you can press down anywhere around the bezel and it's solid, but in the bottom right, it pushes down about a mm or so, then comes back when you release. But it should be solid all around, and it's annoying, and I wonder if it impedes water resistance, etc. So....
Any fixes? Any ideas? Did I just get a bad unit or is this normal? What can I do?

It is the latest greatest noob version from pure-time

 

[nicosuave4201]

Also, with the bracelet, the clasp lock doesn't go down flush all the way. It's almost there, but it won't go flush. I understand this is a common problem? How to fix? Is there a fix?

 

[Snoweagle]

I have a problem with my deep sea. I've had the watch a month now and am just now noticing this.

In the bottom right quadrant of the watch face area, the bezel has a downward flex to it. As in, you can press down anywhere around the bezel and it's solid, but in the bottom right, it pushes down about a mm or so, then comes back when you release. But it should be solid all around, and it's annoying, and I wonder if it impedes water resistance, etc. So....
Any fixes? Any ideas? Did I just get a bad unit or is this normal? What can I do?

It is the latest greatest noob version from pure-time

It's not normal, it should be flushed.

 

[nicosuave4201]

You are responding to my 2nd post, not my first. The first was about the bezel, the 2nd was about the clasp. You are talking about the clasp right? I did some reading and know how to fix that. Now what I need help with is the bezel.

 

[Thrasher]

Here ya go I got this from BK and had VAC mod it, Pretty much the same as what Plankton did. I love it.

 

[Thrasher]

Here is a picture after i did the PP mod on the bezel.

 

[Snoweagle]

You are responding to my 2nd post, not my first. The first was about the bezel, the 2nd was about the clasp. You are talking about the clasp right? I did some reading and know how to fix that. Now what I need help with is the bezel.

I'm referring to the bezel, it should not have any play in it but sits firmly onto the case.

 

[nicosuave4201]

I'm referring to the bezel, it should not have any play in it but sits firmly onto the case.

ok so is there a way to fix it?

 

[Snoweagle]

ok so is there a way to fix it?

I'm not sure the exact procedure but some said to pry out the bezel carefully, check for any broken/worn components then put back the bezel.

 

[nicosuave4201]

ok, thanks..

 

[Snoweagle]

ok, thanks..

Welcome. If you place the bezel on a flat surface, be sure there's no play in it, else means the bezel could at some point be slightly warped.