NEW NTTD No Time to Die Titanium/Titanium Seamaster 007 Edition

[Plenitude]

Today extract of qc

 

[Thatwatchguy]

Still pink hands unfortunately

 

[Plenitude]

And about weight? Gen is 93 gr, 20 gr balance is due to titanium bracelet? Only 20 gr?

 

[Thatwatchguy]

I prefer it on nato but the hands…come on!

 

[bhehe6813]

Still pink hands unfortunately

Those look okay to me actually. Probably just the lighting, you can tell the color is still wrong on the hour and seconds hands.

 

[Shane73]

Ive Had the NTTD V4 for about 18 months now alway been a good time keeper and pinkish hands only noticeable in certain light, Question is recently the crown will not screw back into the case so it is constantly pinged out, Is this common and can it be fixed?

 

[Valaj]

Ive Had the NTTD V4 for about 18 months now alway been a good time keeper and pinkish hands only noticeable in certain light, Question is recently the crown will not screw back into the case so it is constantly pinged out, Is this common and can it be fixed?

Ahh. The infamous tube stripping issues. You can send it to a watchsmith to get it converted to a push pull crown (no screwing down). I know of one person who's managed to swap the stripped crown tube out to keep the screw down system.

 

[Route66]

recently the crown will not screw back into the case

And another one bites the dust
Yes, unfortunately it's the most common failure in VSF SMP's

 

[Shane73]

Ahh. The infamous tube stripping issues. You can send it to a watchsmith to get it converted to a push pull crown (no screwing down). I know of one person who's managed to swap the stripped crown tube out to keep the screw down system.

Thanks for the info, Gutted really its been a good piece up until this.

 

[Shane73]

And another one bites the dust
Yes, unfortunately it's the most common failure in VSF SMP's

Ah great well know issue then? , Is it dead then? Do you know of the best alternative on the market at the minute if the VSF isnt up to scratch, When i purchased this one it was looking like VSF had been closed down and the alternatives weren't good but thats going back a while.

 

[Route66]

Ah great well know issue then?

yes it is, since at least 2 years: have a look here

VS Omega "No time to die" Crown/Tube replacement

I have a problem with my VS factory V3 Seamaster "No time to die" , the crown and/or tube threading seams to be damaged or worn out. Anybody knows if this case would take an gen tube and crown? thx

forum.replica-watch.info

Is it dead then?

No, it's not dead - just do as @Valaj has suggested or follow anyway the suggestions by your local independent watchsmith

Do you know of the best alternative on the market at the minute if the VSF isnt up to scratch, When i purchased this one it was looking like VSF had been closed down and the alternatives weren't good but thats going back a while.

If you have lost any hope in fixing your NTTD, you may try ORF/GO factory for a brand new one
Your TD may tell you if it's available again:

 

[Canales16]

And is this crown problem more common in the NTTD because it is made of titanium?

 

[Kup1712]

And is this crown problem more common in the NTTD because it is made of titanium?

General vsf seamaster line problem, not just on titanium.

 

[Canales16]

The nttd has always been on my radar but with such a common corona problem I don't dare. I have a seamaster and the vsf worldtimer both and still no corona problems. I'll cross my fingers. The one I had the problem with was an ORF.

 

[Kingsandqueens]

The rotor on mm NTTD V4 is so loud, any mods for this possible or is the gen also loud?

 

[Shane73]

yes it is, since at least 2 years: have a look here

VS Omega "No time to die" Crown/Tube replacement

I have a problem with my VS factory V3 Seamaster "No time to die" , the crown and/or tube threading seams to be damaged or worn out. Anybody knows if this case would take an gen tube and crown? thx

forum.replica-watch.info

No, it's not dead - just do as @Valaj has suggested or follow anyway the suggestions by your local independent watchsmith


If you have lost any hope in fixing your NTTD, you may try ORF/GO factory for a brand new one
Your TD may tell you if it's available again:

Thanks for the info!

 

[Kup1712]

Hi, is there a version from VS+ ? Should be 20g lighter and without pinkish lume on the hands. (Saw just one post on Reddit (I know... Reddit))

 

[Valaj]

Hi, is there a version from VS+ ? Should be 20g lighter and without pinkish lume on the hands. (Saw just one post on Reddit (I know... Reddit))

Lol I just saw the post as well. That's a big difference considering they say the bracelet on it is still steel. The watch case is a Ti alloy. 20gms saved just on the watch case sounds kinda off to me.

 

[Kup1712]

Lol I just saw the post as well. That's a big difference considering they say the bracelet on it is still steel. The watch case is a Ti alloy. 20gms saved just on the watch case sounds kinda off to me.

Exactly...just too good to be true

 

[micablue]

I like to know if anyone has tried ordering the GOF/ORF NTTD v2? It looks very promising based on the pictures but it's hard to tell. I am just hoping to finally pick up a NTTD without the infamous crown tube stripping issue from VSF's version.