-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
New AP 26240 with 4401 Super Clone movement is coming
- Thread starter puretime
- Start date
Can you maybe put a slight bend in one of them or hit it with a chisel and Hammer to flatten out a small section of it and create additional resistance? Otherwise last option would be to put a small amount of epoxy on the end of the one side.
The blue dial appears much darker than gen. Everything else appears spot on.
An advantage of this dial is that the gen subdial rings aren't too prominent anyway, so the subdials are closer to gen.
I'm sure they'll find something to screw up so it's not totally correct lol
- 2/5/16
- 1,760
- 1,211
- 113
The rotor of mine, which I received just last week, is rose gold and with the correct font.
Guess I was kinda "lucky", since my original watch was seized and I had to receive a new one... probably from a updated batch. Took four months in total
Nickdev47
Do not accept unsolicited offers
- 8/6/25
- 4
- 6
- 3
I know this has been discussed before but I just wanted to give my option. After staring at the gap on the bezel screws all the time I decided to pull the trigger on new ones. Overall very happy with the figment, although a few of them sit just a hair proud. Nothing too noticeable. Yes I know these were about $230, but I think it was a nice improvement. 1st photo is from QC and the green background ones are the after. Also these are from watch2parts.com
Been debating on if this was worth the expense. Looks good. When tightened, are they flush to are they slightly sunken?I know this has been discussed before but I just wanted to give my option. After staring at the gap on the bezel screws all the time I decided to pull the trigger on new ones. Overall very happy with the figment, although a few of them sit just a hair proud. Nothing too noticeable. Yes I know these were about $230, but I think it was a nice improvement. 1st photo is from QC and the green background ones are the after. Also these are from watch2parts.com
Nickdev47
Do not accept unsolicited offers
- 8/6/25
- 4
- 6
- 3
For me about 5/8 are flush and 3/8 are just a hair above the bezel. The ones that are proud are barely noticeable when i run my finger across them.
- 27/5/22
- 4,584
- 6,873
- 113
thank gawd i have sh!t eyes for such detail IRL
Well, that does look good! Nicely done. I'll have to retry this on my other 26240.I know this has been discussed before but I just wanted to give my option. After staring at the gap on the bezel screws all the time I decided to pull the trigger on new ones. Overall very happy with the figment, although a few of them sit just a hair proud. Nothing too noticeable. Yes I know these were about $230, but I think it was a nice improvement. 1st photo is from QC and the green background ones are the after. Also these are from watch2parts.com
munichman
Active Member
Have you found a solution? I'm in the same boat, I stopped and cannot find a solution.
fletch512
Active Member
- 9/5/06
- 356
- 397
- 63
We finally have some hi-res pics and video of the $320 DP dials on AMOWatch. I haven't closely reviewed all four dials, but the blue dial does look pretty good on first glance.
DP blue dial:
Gen blue dial:
DP blue dial:
Gen blue dial:
I think stick with the stock APS dial for me.We finally have some hi-res pics and video of the $320 DP dials on AMOWatch. I haven't closely reviewed all four dials, but the blue dial does look pretty good on first glance.
DP blue dial:
Gen blue dial:
fletch512
Active Member
- 9/5/06
- 356
- 397
- 63
