-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
Mini review ZZF v3 116610LV HULK, comparison with gen 116610LN
- Thread starter 2841
- Start date
Could you post a close up of the face incl Pearl? It looks like yours is greener than the indices lume. Same as in my QC pics...
antonio220893
Known Member
- 26/8/18
- 106
- 19
- 18
Finally an objective review who doesn't have the prejudices of the people who wrote it. I bought a zzf3 and now I'm going to install a Cristal gen by a watchmaker. I hope that at finally I'll have a rep very close to gen. My only fear are about the dial and bezel color.
2841 about the color of dial and bezel of the v3, what do you think? (I've never had a gen hulk to compare him).
2841 about the color of dial and bezel of the v3, what do you think? (I've never had a gen hulk to compare him).
Thanks bud
I sadly haven't had a gen Hulk in hand the last 6 months, so i'm going from memory here. The v2 and the v3 is slightly different in color, its like they toned the v3 down a bit. As in regards to the color vs gen. If you put it next to a gen, you will see a difference, but i dont think theres going to be a lot of people in the world who can point out whats correct and whats wrong Its mostly OCD guys like us here, that's going to spot the difference. My honest opinion, damn good rep, and no one is going to call this on the wrist, BUT if you wanna make it feel special... Gen crystal, and a rebrush
Thanks bud, appreciate it
There are some more detailed pics of the brushing on one of my sales treads (Scrool down) https://forum.replica-watch.info/forum/replica-watch-sales/9414371-franken-hulk-116610-lv
scottiedog
I'm Pretty Popular
- 15/7/16
- 1,404
- 394
- 83
antonio220893
Known Member
- 26/8/18
- 106
- 19
- 18
Gen Crystal is in uploading ???????? the watchmaker installing it in a few days.
For the rebrushing I’m thinking about use it for many times.. and after I’ll do it. Do you think it’s a good idea bud? @2841
Inviato dal mio iPhone utilizzando Tapatalk
antonio220893
Known Member
- 26/8/18
- 106
- 19
- 18
If you wanna do a complete case and bracelet rebrush, you need to do it while the bezel if off. (Btw this is not equal to a restoration, it's simply a light correction to the factory brushing)
[mention]2841 [/mention]
Is it simple to rebrush? How much force is needed? Is it just a pass through
Is it simple to rebrush? How much force is needed? Is it just a pass through
It takes some practice. First of all, you need the right tool (Bergeon blocks) and you need IMO a gen to match.
I had a couple of old noob bracelets that I practiced on, after that, it was trial and error until I found the combination that looked like my gens.
I spend about 2 hours on a bracelet, and finish of with a complete disassemble, cleaning and oil bath.
- 24/10/17
- 3,522
- 5,721
- 113
AGGGGGGHHHHHHH!!!!!
You had the bezel off and didn't take a photo of the insert version on the back!!!!
I would have given you an A+ but now it's a C-
You had the bezel off and didn't take a photo of the insert version on the back!!!!
I would have given you an A+ but now it's a C-
Ha ha ha, maybe i did, maybe i didn't
No to be honest, if everything is okay with the insert and its alligend, i would rather not mess with it. I had one crack before, not a great feeling
My opinion, same as v2s, but the pearl looks better (Whiter)
I wanted to thank every one of you including the post op for the wonderful review and information. I don't post much but enjoy reading and learning from everyone. I have a cheap noob hulk that after reading this review and replies among others I finally pulled the trigger on a ZZF Hulk V3 from my TD intime. I will try to post pictures when I eventually get it.
Sent from my SM-G988U using Tapatalk
Sent from my SM-G988U using Tapatalk