-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
CF Pepsi picture leaks BLRO
- Thread starter wolfiqar
- Start date
Björn_Ironside
I'm Pretty Popular
The scallops on the BLRO are smaller than the standard 116710 bezel scallops as the polished angle is also different along with the bottom angle… on the BLRO the bottom relief angle almost touches the scallops as where the BLNR has a flat spot under the scallops. I’ll update when I get mine… need to buy a new lathe so hopefully I’ll get it done soon
Sent from my iPhone using Tapatalk
Nice work, so the insert is not pressure fit at all? And will have to be completely glued back in?
Sent from my iPhone using Tapatalk
- 17/8/18
- 560
- 220
- 43
Björn_Ironside
I'm Pretty Popular
Replisimio
I'm Pretty Popular
Slightly disappointed it’s not friction fit but I guess it’s a little less resilient being joined the way it is. Thanks for sharing your findings it’s a big help
Sent from my iPhone using Tapatalk
Björn_Ironside
I'm Pretty Popular
i
Rejected for the white points on the Gmt Hand, but seems to be a second batch with a new serial and only one “3” ;-)
don't understand why white dots on GMT ... however the single 3 is random. you may have a next QC with two 3 ;
Last edited:
Replisimio
I'm Pretty Popular
Rejected for the white points on the Gmt Hand, but seems to be a second batch with a new serial and only one “3” ;-)
Mine is first batch with only one flat 3 in the serial so that means nothing.
Sent from my iPad using Tapatalk
Ok, i understand guys, but for me the “3 issue” is not a problem….the white dots on Gmt hand are not so nice, but i see it after giving GL to Lana (JTime)….hope i am in time to change to another one….(need glasses, I am old, ok…..tomorrow will be 49!!)
Replisimio
I'm Pretty Popular
I assume you mean the marks near the pinion on the red hand. Looks like a poor paint finish.
Sent from my iPad using Tapatalk
- 12/3/18
- 34,663
- 66,755
- 113
They used the standard double-sided tape ring, and a new one should be installed for replacement. They are ultra strong and refitting an insert with one can be mildly challenging because the insert can stick before you want it to, and be misaligned.
https://www.ebay.com/itm/174282841898
Note that these tape rings don't always fit the space in a bezel well perfectly. They can be cut into halves or thirds or quarters as necessary to be equally distributed around the well. Coverage does not need to be continuous. Care should be taken not to let the outer edge of the tape ring ride up on the wall of the bezel well. Some folks may prefer to attach them to the insert first, I find it easier to control their placement by attaching them to the bezel well first. The tape rings should never be touched with fingers, the adhesive becomes compromised easily. I use two pairs of tweezers. (Edward Tweezer Hands, lol).
To ensure the insert is aligned perfectly on reinsertion, I put a small thin obstruction across the bottom half of the bezel well. A strip of a dial protector works well for this. You can also use pegwood or a toothpick but be careful not to let it roll out. Then gently set the top indicator (24 in this case) to 12 o'clock. Then you can take your time evaluating the position, get a second opinion from someone, take a pic, etc. so you are certain it's right. If it's not, the insert will lift out easily from the bottom.
Using this technique will keep the insert from falling into the well misaligned, which means starting completely over with another removal, re-taping, and reinsertion. Not fun trust me, haha.
One other very important point about doing this. The rep factory tape may be thicker than the 3M. So I always test fit a 5mm or so arc of the tape into the well and place the insert. I use the obstruction technique for this too, or you can put a piece of scotch tape on the backside of the insert to facilitate pulling it back out.
If one layer of the 3M tape is insufficient, I add a second layer and reassess. I've used as many three layers on some installs. More than that and I switch to a different tape, use a spacer, or an epoxy glue bed, etc.
Last edited:
What’s the actual power reserve on this bad boy? When they start arriving, can someone please fully wind the watch and see how much power reserve there actually is? Please and thank you.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- 12/3/18
- 34,663
- 66,755
- 113
That's for a pack of 10 bro. Plus the center circle is the same material. I cut arcs from the center circles and use them in thirds or quarters, etc. You can do at least three insert installs with one tape ring, at $0.93
Last edited: