Anyone tried to put the JF15202 on the sead quartz 15202? I heard the JF quality bracelet is much better.
-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
Best 39mm Royal Oak AP
- Thread starter Suux88
- Start date
BIONONE
Respected Member
- 28/4/17
- 3,646
- 2,866
- 113
gilrob
Legendary Member
Puretime has JF bracelets listed in their accessories section. Contact them to insure it's the proper size.
Well my current clasp is not being tightly closed enough therefore I thought this was a viable option. Any way to get a new clasp or new clasp screws?
BIONONE
Respected Member
- 28/4/17
- 3,646
- 2,866
- 113
trial and error with this unknown rep maker version which is completely off specs. to find screws that fit is probably the easy part if you are abled to source various sizes with specific threading. To source a new clasp is going to be the harder part as it is not cost efficient for the rep makers of such low end models to sell parts separately.
But you can try of course - just ask the seller who you brought your watch from - worth a try
gilrob
Legendary Member
You'll have to closely examine the clasp mechanism to see what is causing problem. The two locking pins may not be going down deep enough into the elongated opening to engage the locking tabs that is part of the push release. If this is the problem, file off some of the metal above the elongated opening. Also if the two ends of the clasp that butt against each other when the clasp is closed is binding, file off some the metal. Look thru the elongated hole and press the release, check to see if the locking tabs are working properly. If not, disassemble the pushers, clean and reassemble.
Hope this helps.
- 28/5/19
- 822
- 767
- 93
(Sorry for my English)
I present to you my 15300. As soon as it is fixed, it is an old replica of some years ago with a case of the same thickness as the Gen.
It had screws on the lower ring, and a dial with a small logo.
Once the screws are in place (they are passing) the dial is changed, with the lumen inserted between A and P.
What do you think?
First:
After
I present to you my 15300. As soon as it is fixed, it is an old replica of some years ago with a case of the same thickness as the Gen.
It had screws on the lower ring, and a dial with a small logo.
Once the screws are in place (they are passing) the dial is changed, with the lumen inserted between A and P.
What do you think?
First:
After
Yeah, I'd like that also. Quartz (thin) version with a nicely finished case and bracelet. 15202 is all about thinness and finishing, and it has no seconds hand. Instead of spending resources on copying the rotor/ mechanism that anyone can tell immediately it's a rep, put a metal caseback and finish the hell out of the bracelet/dial. I'd buy that.
/end rant
gilrob
Legendary Member
gilrob
Legendary Member
I thought I'd post this here rather than creating a new thread and share it with the 15202 fans. The watch features a pink gold-tone dial, 18-carat white gold case/bracelet and sells for $55,400.00. Perhaps JF, DC or even Z+F could make their own version(s).
https://www.audemarspiguet.com/en/wa...202BC.OOBC.01/
https://www.audemarspiguet.com/en/wa...202BC.OOBC.01/
Last edited:
bigtiddygothgf
Active Member
- 7/10/18
- 322
- 146
- 43
Would love to see a 15202BC rep. Anyone know if any factories are going to replicating it?
Sent from my ONEPLUS A6003 using Tapatalk
SHB
Mythical Poster
gilrob
Legendary Member
SHB
Mythical Poster
This one is sexy.
DC factory sell the blue dial with champagne DW and gold markers, and i think they do the champagne dial as well. Also i do remember seeing a 15202 with salmon/champagne dial up for sale m2m. Edit: https://dealerclocks.to/catalogsearch/result/?q=15202
Last edited:
Do you mean the bracelet of the quartz is as good as JFs?
I just received my quartz from Sead and had the same idea...
Gesendet von iPhone 11 Pro Max mit Tapatalk