- 12/3/18
- 34,663
- 66,755
- 113
ROF GMT with a Molotow flood fill. These markers are pretty good OOTB but I wanted to help hide the slight border joints, and make them a little brighter in low light.
-
Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!
KJ2020 paint mod
- Thread starter Doglover
- Start date
ProGamer73061
Renowned Member
- 12/3/18
- 34,663
- 66,755
- 113
VRF Max insert is the same as the ROF so if you are getting a new VRF, you can achieve results like I showed above. The earlier V1 VRF inserts are not the same.
ProGamer73061
Renowned Member
Thank you. Can i post a QC if they arrives? To identify
Gesendet von iPhone mit Tapatalk
What do you think of this "molotow mod" paint marker?
It's recommended for touching up car paint, it's certainly a stronger paint than acrylic (molotow), but then it's more complicated to remove this excess paint on the bezel of the Watch?
Or is this colour as good as the molotow colour?
KJ2020 what do you think?
It's recommended for touching up car paint, it's certainly a stronger paint than acrylic (molotow), but then it's more complicated to remove this excess paint on the bezel of the Watch?
Or is this colour as good as the molotow colour?
KJ2020 what do you think?
Last edited:
- 12/3/18
- 34,663
- 66,755
- 113
What do you think of this "molotow mod" paint marker?
It's recommended for touching up car paint, it's certainly a stronger paint than acrylic (molotow), but then it's more complicated to remove this excess paint on the bezel of the Watch?
Or is this colour as good as the molotow colour?
KJ2020 what do you think?
Never tried car paint bro, but spray paint is enamel so what you show there would not be any harder to remove. Use a razor blade first then some kind of thinner.
I would be more concerned about how it has to be applied and how uniformly it dries. Will pen strokes be visible, etc.
I think it is better if I continue to use your tried and tested method with "molotow".
Alex_oz
Known Member
- 8/10/20
- 168
- 73
- 28
Hey guys, how do you waterproof your mods? I mean I've tried Molotow and Posca, and both tend to come off or become uneven if the watch gets wet (dish washing, hand washing or smthng). I removed the Molotow out of my bezel with nail polish remover and toothpick, but i just wanna make it a longlasting mod LOL
I also had the same problem with durability.
I've thought about using car paint or even nail varnish, but I don't know if I'll damage the ring nut with that kind of paint, but it certainly lasts a lot longer than acrylic paint.
ROF GMT with a Molotow flood fill. These markers are pretty good OOTB but I wanted to help hide the slight border joints, and make them a little brighter in low light.
Hey KJ2020, did you leave the insert with the watch or was this taken apart? I want to do the flood fill on my VRF MAX but I don't have the tools to take the insert apart.
- 12/3/18
- 34,663
- 66,755
- 113
You can do the flood fill mod with the insert still on the watch bro. If you are careful, there is hardly any wiping to do at all. The VRF/ROF markers are so deep, just fill them to level, let them dry a little, fill them again and done.
I have now ordered one of those posca pens too and have also no tools to lever down the bezel. Will tape the bezel slightly and then do the paint job. I think that is enough to minimize the rest potential of fucking up something.
ben_a34
Known Member
- 30/7/20
- 136
- 181
- 43
Wouldn't worry too much. It is pretty forgiving - basically doesn't stick at all on the glass or bezel insert, only on the engraved bits.I have now ordered one of those posca pens too and have also no tools to lever down the bezel. Will tape the bezel slightly and then do the paint job. I think that is enough to minimize the rest potential of fucking up something.
I would say though, that I thought the posca pen paint was OK but left an uneven finish that I was never completely happy with. In the end I got hold of some molotow paint and that worked great. It's almost unbelievable how even the final finish looks.
here we go!
May I ask you why you chose to use the 'POSCA' marker instead of the 'MOLOTOW'?
First, because the master of DIY paintjob wrote this:
And secondly, the Posca was easier for me to get and has the narrower tip. I thought that would make it even easier!
And secondly, the Posca was easier for me to get and has the narrower tip. I thought that would make it even easier!
Last edited:
SuperLory
Well-Known Repist
- 22/10/15
- 8,455
- 5,046
- 113
Massive kudos to KJ2020 for his help
I had successfully revived a dull noob daytona ceramic bezel with the posca flood technique
Incredibly effective and stupidly easy.
I'm taking it to a slightly higher level now mixing silver and white on the plastic mat and then flood with the help of a superfine brush
I had successfully revived a dull noob daytona ceramic bezel with the posca flood technique
Incredibly effective and stupidly easy.
I'm taking it to a slightly higher level now mixing silver and white on the plastic mat and then flood with the help of a superfine brush
AASoliman
Known Member
Massive kudos to KJ2020 for his help
I had successfully revived a dull noob daytona ceramic bezel with the posca flood technique
Incredibly effective and stupidly easy.
I'm taking it to a slightly higher level now mixing silver and white on the plastic mat and then flood with the help of a superfine brush
Make sure to update us when its done!
SuperLory
Well-Known Repist
- 22/10/15
- 8,455
- 5,046
- 113
you see I didnt take a photo before and after so it would not be of great use showing it how it is now; the main point we should consider and take back here is that this is an inexpensive but highly effective solution.
I spent :
$2 for uniposca silver
$2 for uniposca white
$3 for superfine detailing brush
$5 for a box of 100 individually sealed alcohol (isopropyl 70%) swabs
and the results are stellar, you can't see any lump or defect or anything..it seems perfect to my bare eyes - i dont have nor would use a loupe anyway. Where in dim light it was an almost black bezel, it is now a very luminous, legible bezel.
Furthermore the process is extremely quick (20-30 minutes) and you can just go few rounds of floods (i'm at 4 altogether) without noticing lumps or uneven spots.
Anyway here's an indoor (sunlight from the open windows) shot
Next one I do I'll try to be more detail-oriented. And yes I regret having paid so much money for a CF bezel for another daytona I have. (not that CF is worse, it's just FOR ME I would be more than happy with the posca flood bezel)