Jubilee on Daytona

[Amguy1]

Anyone on here put the latest ZZF Jubilee bracelet on Daytona ? If so would love to see especially on the panda. Seen this on Instagram

Sent from my iPhone using Tapatalk

 

[thinker1]

It’s purely subjective but jubilee in my POV goes well with simplistic dials e.g, GMT, Sub date just etc.

Daytona face with its sub dials/hands and jubilee get very cluttered overall aesthetically.

 

[srhoque]

This combo is not sitting well with me. Daytona (for that matter any stainless sports model) is made for Oyster. Just my POV

 

[tgfrulez]

Same question here
On IG I saw many Tona with jubilee: Super Jubilee from DJ with the hidden clasp.

I would prefer instead the GMT jubilee but which one fit the Noob?
I was thinking about the VRF one but..

 

[Giellea]

daytona noob with arf super jubilee

 

[Last_man_standing]

^^ Wow that looks awesome.

 

[Amguy1]

daytona noob with arf super jubilee

That’s stunning


Sent from my iPhone using Tapatalk

 

[thorne]

I have a WG Daytona incoming with both the VRF Jubilee and the ARF Super Jubilee. Will post pics on both bracelets when it’s here.

 

[thorne]

Can confirm the ARF 63600 does NOT fit the WG Daytona case. There’s a large gap and the endlink swivels around the springbar.

I’ve also got a VRF Jubilee bracelet from their 116710, but I need thinner springbars for it. When I get that sorted I’ll post some pics. Hopefully it’s better than the ARF.

 

[thorne]

Nope, VRF Jubilee doesn’t fit as well.

Oh well. Back to the stock Noob for now.

 

[KJ2020]

Nope, VRF Jubilee doesn’t fit as well.

Oh well. Back to the stock Noob for now.

You could try putting some tape on the lower lip of the case to see if It would help. You can actually tell if it would or not by just lifting up on the bracelet from underneath and see if the top of the SEL will swivel enough toward the case without an unacceptable reverse recess (SEL backend upward protrusion). Changing the diameter of the springbar can alter these results as well.

 

[thorne]

You could try putting some tape on the lower lip of the case to see if It would help. You can actually tell if it would or not by just lifting up on the bracelet from underneath and see if the top of the SEL will swivel enough toward the case without an unacceptable reverse recess (SEL backend upward protrusion). Changing the diameter of the springbar can alter these results as well.

Ah let me try that, that does look like it would work.

 

[KJ2020]

Ah let me try that, that does look like it would work.

That's a stack of 5 pieces of bracelet tape I used, about .15mm thick IIRC. I had to trim it up some as it initially showed underneath, protruding from between the case and the SEL. I should have just used the other piece left hanging in the first pic! It's held up fine, once the SEL is installed it can't go anywhere.

 

[thorne]

Tried the tape, the GMT bracelet still has some swivel. Noticeably less with the tape though.
Put the oyster back on as I felt the Jubilee bracelet + Daytona overall looked too busy.

 

[James2020]

Tried the tape, the GMT bracelet still has some swivel. Noticeably less with the tape though.
Put the oyster back on as I felt the Jubilee bracelet + Daytona overall looked too busy.

Agree.

Thanks for trying and sharing your results! :clap_1:

 

[thorne]

Found this pic on TRF. Gen Daytona, gen 63600.

You see the gap between the endlink and the watch case, it’s the same fit I get with the rep.

 

[ashu2289]

Get a BP 116710 Jubilee and it would snug fit ARF, Noob as well as Gen. Tried on all three cases

 

[rankiba]

Get a BP 116710 Jubilee and it would snug fit ARF, Noob as well as Gen. Tried on all three cases

Which gen case model did you try it on? I'm looking for that jubilee daytona look as well.

 

[TYL88]

I think the 116500 looks nice on jubilee. I bought the jubilee locally, some spring bars i tried have bad gaps on it. Then i opened my drawer and tried all the spring bars and it worked.

Btw i dont know what factory is the jubilee, the code is 5LX on the clasp.

Sent from my SM-N985F using Tapatalk

 

[rankiba]

I think the 116500 looks nice on jubilee. I bought the jubilee locally, some spring bars i tried have bad gaps on it. Then i opened my drawer and tried all the spring bars and it worked.

Btw i dont know what factory is the jubilee, the code is 5LX on the clasp.

Sent from my SM-N985F using Tapatalk

Looks good, I'm surprised a non-superjubilee could fit. Can you check the end links and check what was the stamped code inside the connector of the end links?