• Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!

What mods to the V6 AP?

R0L3X

Active Member
13/1/13
221
3
0
Hello folks,

I just got my V6 AP Diver. Great piece but there are a few things that need to be improved imo:

- Hands don't match that well with the dial
- High-beat movement should me low beat
- Crystal cyclops - date looks a little bit cloudy
- Some minor factory dirt on the hands

I see some people installed a new crystal with AR on their Diver. However, gen AP doesn't have AR??!

What mods to do? A relume maybe?

Thanks!
 

takoxavy

I'm Pretty Popular
8/3/14
1,341
26
38
It is how much you are willing to accept the flaws of the rep. No point doing so many mods lol.
 

TimeDelux

Renowned Member
10/5/14
784
35
28
I would AR and Clean first.

and if you have too much money go for the low beat movment.

Dont forget to sink the screws if they pop out.

Cyclops is way too small of a flaw on mine.


4RngNML.jpg

NjqdZVS.jpg
 

R0L3X

Active Member
13/1/13
221
3
0
Thanks.

So gen does have AR on the whole crystal? Any recommendation as to which crystal looks closest to gen?

@ TimeDeluxe: Your's looks great. Is that a 5.1? Since the lume looks a little but off-white

I owned a 5.1 and a V3 in the past and both had some inner rotating struggles. My V6 seems to be slightly improved but turning too fast will make the ring clack. Is this a technical flaw or something that's fixable by a mod?

All I can say is that the rubber of the V6 is terrific.


GEN: Seems to me it has no AR?
AUDEMARS+PIGUET+Royal+Oak+Offshore+DIVER+04+.jpg
 

TimeDelux

Renowned Member
10/5/14
784
35
28
So mine is a V6 and the inner ring caused a few issues at first but now its screwed tight.
 

R0L3X

Active Member
13/1/13
221
3
0
So mine is a V6 and the inner ring caused a few issues at first but now its screwed tight.

Did you do any mods on your V6?

Is there any way to get the very white lume like gen? All reps I have seen have this kind of off-white lume.

Too bad a gen dial is not an option
 

TimeDelux

Renowned Member
10/5/14
784
35
28
AR is the most obvious mod and sunken screws.

Well The lumen makes it sort of greenish some times
 

SSTEEL

Banned
Banned
30/1/13
3,803
1
0
I have a V5.1 on bracelet, and a V6 on rubber. I have done a few small mods on the V5.1 so far, fitted a bracelet, sunken the bezel screws, and waterproofed it and WR tested to 6ATM. It passed. I have a Mineral crystal from Domi/Guru with colourless AR, not sure which Dive to fit it in.
 

heero

Known Member
29/3/13
145
0
0
Does the GEN have an AR crystal? It certainly doesn't look like it.
 

valante

I'm Pretty Popular
20/2/13
2,043
1
0
Hello folks,

I just got my V6 AP Diver. Great piece but there are a few things that need to be improved imo:

- Hands don't match that well with the dial
- High-beat movement should me low beat
- Crystal cyclops - date looks a little bit cloudy
- Some minor factory dirt on the hands

I see some people installed a new crystal with AR on their Diver. However, gen AP doesn't have AR??!

What mods to do? A relume maybe?

Thanks!

Ok, Here's the improvement you can do with V6:

1.> Relume Hands, - as they have a different colors with the stick lume and inner bezel lume.

2.> Relume the Numbers - this due to sloopy lume and unconsistence of the v6 factory lume on each watch. FORGET THAT THE REP WILL EVER COME CLOSE TO GEN LUME NUMBERS! so here is the explenations - Gen print a white base number on the inner bezel, this print is very wide, but they didnt lume all the base, they only lume some of it, this create a lume with a borders in it. AND THEY USING A CNC MACHINE to lume the numbers, so its so straight, so consistence with the white borders on the base plate of the inner bezel!
Heres the pics, notice how it has a numbers have a white consistent base on it.

Pay attention on the 5 and 0

3.> im in the borders for AR crystal as the gen did not have AR, but the crystal is so clear but makes reflections. with rep crystal is cloudy but if you DAR, it will look no glass at all, which a tell too, single inside ar might be the answer but i havent see what it looks like.
See how reflective but clear in this pics: if we dar the crystal, there will be no reflections like this anymore:


4.> DAR the cyclops.

5.> NO ONE can tell slow beat or high beat unless you put then gen side by side! so i dont know wheter their mods will be worth the money.
here's the video of gen slow beat and rep high beat.


6.> Do the movement service if you think the watch is a keeper, since the factory movement came up dry and dirt in some parts. Leaving it running without oil for some time will damage some parts and make it useless if you servics it later on.

7.> Sunken mods - this for me also not so important. This cult of sunken bezel happens because AP diver advertising pics, have a very dep sunken bezel, and everyone thought that the bezel has to be sunken, but this is wrong! not every gen has a sunken bezel, some of them only level, so as long as your screw dosent pop out your fine, you can adjust it until level or sunken its your choice.
Here the ad pics that every one refers to:


you can see how sunken it is
but look on my gen diver, it just level:


8.> one thing that people forget is how easy to tell a rep diver due to the buckle. rep buckle is still very far from the gen. So invest on a gen buckle is a good thing if your diver is a keeper.
Here some review gen and rep buckle:
http://forum.replica-watch.info/vb/showthread.php?t=178036