Replacement Screw for ExpII Clasp - Can’t find a match

[Duc]

I lost the screw from my Noob ExpII clasp and have not been able to find a replacement. Does anyone know the thread pitch for this clasp screw?

I’ve bought and returned a few sets of replacement screws that’s were advertised for the Exp II but they were either too long or the screw pitch was incorrect. Desperate for help.

 

[KJ2020]

I lost the screw from my Noob ExpII clasp and have not been able to find a replacement. Does anyone know the thread pitch for this clasp screw?

I’ve bought and returned a few sets of replacement screws that’s were advertised for the Exp II but they were either too long or the screw pitch was incorrect. Desperate for help.

Is it a link screw or a pin? Is there another one similar to it on the other side of your clasp?

There are a couple dozen different sizes of Rolex link screws. Maybe a pic of where exactly it goes would help us point you in the right direction.

 

[Duc]

Thank you. I look a picture of where the screw I’m missing goes. It is connected to the link on the clasp.

 

[KJ2020]

Ok I looked at your pic. This link screw is not exposed on the far side correct?

I took one of mine out. This is what I would try next

Length 13.5mm
Width 1.5mm
Thread diam 1.0mm

Look on ebay, or Ali Express. Should be able to get a set of 2 for under $10. Good luck.

 

[Duc]

Amazing, thank you! I just happened to find the Rolex part number as well - 32-20638. Maybe I’ll find someone that sells it.

 

[KJ2020]

The gen screw is probably $30 or more for one, aftermarket is your best bet.

 

[alligoat]

And a gen screw might not fit your rep bracelet. Too bad you don't have an extra link which you took out of the bracelet and you could use that screw. If you get a screw that fits, you might use a dab of glue to keep it in place next time.

 

[Duc]

Can’t use another screw. The specific clasp screw I need is shorter than all the others. It is unique to that one clasp socket.

 

[Carbon Summit]

Looking for link screws for a couple of my watches. Did you ever find one that worked for your watch?

One of the watches I'm looking for is a ARF 116610LN V3 and the other one is a gen 216570.

Did you ever find out if the gen replacements worked for your rep?

I'm looking for Rolex part numbers 32-20687 and 32-20638. I don't care if they are really genuine Rolex but the same sizes.

 

[Hazing]

Looking for link screws for a couple of my watches. Did you ever find one that worked for your watch?

One of the watches I'm looking for is a ARF 116610LN V3 and the other one is a gen 216570.

Did you ever find out if the gen replacements worked for your rep?

I'm looking for Rolex part numbers 32-20687 and 32-20638. I don't care if they are really genuine Rolex but the same sizes.

They sell screw kits that have a number of sizes but in my experience, they have everything but what you need. although they do usually have the most common sizes.
https://www.dhgate.com/product/scre...f015fc50de47d6421||418955412|#cppdh-13-3|null

Theyre also available on amazon and ebay as well .

 

[Carbon Summit]

It shouldn't be so hard to order replacement generic link screws!

 

[Duc]

There’s a seller on eBay that had 3 different screws the correct length I was looking for (clasp screw, NOT link screw), but none of the three were the correct pitch. Ultimately, I bought a trashed rep bracelet that had the screw I needed.

sorry I’m not more helpful.