• Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!

116519ln Noob v2 just arrived

pyter77

Active Member
27/1/20
217
41
28
my movement is SA4130 and it goes on for almost 25/30 seconds a day, I think it should be regulated and there is nothing to worry about

philwongnz please explain to me better, you mean the R of UNITS PER HOUR
 

tom_h

You're Saying I Can Sell?
15/2/20
37
6
0
pretty confused about the v2 and v3 talk.

i just had a look on puretime and it only shows v2 as the latest.

where can the v3 be found???
 

MadWatcher

Known Member
20/3/19
188
82
28
I thought the silver 116519 and 116509 used the same dial but I notice the coronet on the 116509 on intime's website look crappier then the one on the 116519. I almost pulled the trigger on a 116509 and was going to put a CF bezel on it until I saw that coronet. Can anyone confirm if the dial is different?

116519 dial
daytona-116519ln-904l-v2-noob-1-1-best-edition-silver-gray-dial-on-rubber-strap-sa4130-free-rubber-strap.jpg


116509 dial
daytona-116509-904l-ss-case-noob-1-1-best-edition-gray-dial-on-ss-bracelet-sa4130.jpg

I just got QC pics for the 116509 and the crown looks like the crappy coronet in the second picture :facepalm:. I think the dial they used on the 116509 and 116519 might be different
 

vik2001

You're Saying I Can Sell?
26/3/14
78
7
8
How easy is it to shorten the rubberstrap? I have small wrists. Is it easy to cut back?
 

Tony Clifton

Renowned Member
7/2/20
598
469
63
Germany
How easy is it to shorten the rubberstrap? I have small wrists. Is it easy to cut back?

You can not cut the Oysterflex. However with the Noob you will get a set of "normal" and "short" sized straps. In combination with the different fixing Points in the clasp and by
using the two small Oysterflex bands
you will get a good fit, even with a small wrist.

May I ask how big is your wrist?
 

RonP

Renowned Member
11/10/19
559
272
63
UK
I have just got my QC pictures for this watch and I have a couple of issues.

1. It seems to me that there is a bigger gap between the 3 o clock marker and the right subdial than there is between the 9 o clock marker and the left sub dial.

Is that the case or is it the camera angle or am I seeing things? I have marked out the two areas in red.

2. Is the dial slightly crooked towards the left?

Any input would be much appreciated.

ZZ313i.jpg
 
Last edited:

RonP

Renowned Member
11/10/19
559
272
63
UK
What do you think about the Rolex logo on the dial? It looks slightly crooked to the right hand side. Look at the 12 o clock marker.

Is this a valid reason to reject or is it being pedantic?


 

enduser

Renowned Member
Patron
Certified
29/7/20
559
414
63
UK
Looks fine to me - the watch is slightly tilted in the photograph anyway. Even if there was a "fault" you'll never see it unless you enlarge 10x. Nice watch.
 

Duckber

I'm Pretty Popular
16/8/19
1,585
864
113
Question, do the hands on the subdials look vertically upwards? I had to QC a couple times cause the previous ones had tilted hands. This seems okay to me but would like an extra opinion or two if possible...