• Tired of adverts on RWI? - Subscribe by clicking HERE and PMing Trailboss for instructions and they will magically go away!

Full review of the VSF 8500 clone movement *Pic Heavy*

Swerepguy

Active Member
12/2/18
287
92
0
santre22 Do you think it is possible to do this without any previous experience in servicing watches, just using your detailed instruction? Or will it end up with a spectacular failure and the need to buy a new watch?

No way! Buy a cheep one first and try. U will fail.
 
  • Like
Reactions: wilsonpepper

jmk81

You're Saying I Can Sell?
4/2/20
32
7
8
EU
No way! Buy a cheep one first and try. U will fail.

That's what I thought. So I guess I'll just translate instructions, print them with pictures and take it all to my local watchsmith to see if he's rep friendly :)
 
  • Like
Reactions: Mille M

Migueldef1

You're Saying I Can Sell?
31/1/17
80
17
0
The "problem" it's all the "hardware" necessary for the service and of course: know-how and practice it's crucial for these kind of work.

Do not forget that you are looking to pictures that are amplified. ;-) About me, I'm not able to do it, it's needed a steady hand that I do not have (and to be fair, also don't have the know-how and practice).

This topic is the best tutorial that I ever saw about service in reps, so your local watchsmith with the prints, for sure that can handle the job. ;-)
 

CaptainSplash

I'm Pretty Popular
11/8/19
1,457
1,609
0
santre22 Do you think it is possible to do this without any previous experience in servicing watches, just using your detailed instruction? Or will it end up with a spectacular failure and the need to buy a new watch?
I have a Breitling Navitimer GMT with a A7750. Thought I'd service it myself. I now have a replacement Navitimer GMT on the way. This one I will NOT service myself.... :D. I also have a custom annual calendar IWC Portugieser, which has to be shipped back to ZF in China because my local watch repair shop had a meltdown when they realised how complex it is, no way that you could service that if you don't have the practiced skills and a steady hand.

My own mental note: find a rep friendly repair shop that is willing to take a chance on the custom stuff, or stick to the Valjoux or ETA clones, or even Miyota/Seagull, if you want to keep things serviceable.

Sent from my SM-G975F using Tapatalk
 

jmk81

You're Saying I Can Sell?
4/2/20
32
7
8
EU
I have a Breitling Navitimer GMT with a A7750. Thought I'd service it myself. I now have a replacement Navitimer GMT on the way.

Yeah, I can picture myself in exactly same spot :D

My own mental note: find a rep friendly repair shop that is willing to take a chance on the custom stuff, or stick to the Valjoux or ETA clones, or even Miyota/Seagull, if you want to keep things serviceable.

Little to late for that second option, so as I said gonna translate this thread, print it out and make a journey through repair shops in the 'hood.
 

tom86

Divers only
Supporter
Certified
28/7/19
149
155
43
EU, UAE
I was reading through the thread, but the size of the winding stem was not mentioned. There are two sizes of 7750 winding stems, the 0.9mm and the 1.2mm. Is it the 1.2 in the 8500 clone? Thanks!
 

DrBJSteiner

Horology Curious
28/2/19
15
2
0
I had mine serviced by StRodda....fast service and excellent work...he even sent me pics when it was disassembled because I was curious.
 

ower

You're Saying I Can Sell?
3/8/12
59
26
18
This would deserve a sticking to top.
 
Last edited:

Max111

You're Saying I Can Sell?
15/3/19
49
15
8
Thank you for your review
 
Last edited by a moderator:

NaviChief

I'm Pretty Popular
30/8/06
1,171
855
113
Thanks for this, it is tremendously helpful. Did you service the mainsprings and reapply braking grease to the barrels?
 

spaceman007

Active Member
5/1/22
212
53
28
Has anyone tried to do this with a VSF omega Spectre 300 with the clone 8400 movement? My rotor is stuck and need to try to unstuck it lol
 

santre22

I'm Pretty Popular
22/3/12
1,646
338
83
I just want to give an update after about 4 years since the service of this watch.

I have been using the watch almost daily and when using other watches it have been mostly in the watch winder so pretty much continuously running all the time.

It still running amazingly accurate, around +5 seconds in a week. In the Timegrapher it still reach about 290-300 amplitude when fully wound. Power reserve haven’t been tested as it’s on the wrist or in the winder. But due to the amplitude probably really good PR anyway.

Beside normal everyday wear at the office I’ve also used it in -25 degrees Celsius skiing and in hot summer weather at the beach. Even snorkeling probably down to 5 meters without any problems. Before holidays each year I go to a small watch shop to have it pressure tested as I don’t have the equipment just to be sure.

There are some hairlines to the case but it hold up amazingly considering I’ve used in the garage sometimes booth welding and working on my car.

Approx. 350$ for this much enjoyment is hard to beat. It sparkles in the sun and I love the watch!

 

Ema79

You're Saying I Can Sell?
25/12/18
95
5
8
I've promised to make this post since before Christmas but I had no time until now. So this is a complete service of a VSF 8500 clone movement in my planet ocean.

IMG-7770.png

So lets start with opening the caseback.

IMG-7771.png

Then release the stem by pushing firm on the lever in the red circle.
It's close to the print SWISS. The first time I tried I was too gentle,
just start that way and apply little more force until the stem are released when pulling the crown.

IMG-7772.png

Next up is to remove the rotor. This one is tricky, the construction isn't near the genuine 8500. You have to carfully take a small screwdriver (Bergeon 30009 White) the with of the blade is illustrated in red on the picture. When you are under the washer with the tip just gently wiggle the screwdriver untill it's lose. On to the next picture.

IMG-7773.png

Here the washer is lose (orange arrow) under it we have a tiny mirror/plate (red arrow) that have sticky glue that sits on the rotot screw, just be carefull as this little plate easy stick to the tray or box where you put it under the service.
The yellow arrow show the amount of glue that hold the washer its a bit darker shade of gray.
I think with the chinese QC this would differ alot between the VSF watches with "Super" clone movements. That means some will be easy to remove some quite hard as mine was.

IMG-7774.png

Here it's just a normal rotor screw, probably directly from a A2824-2
Also the rotor bearing seem to be quite similar to a A2824-2.

IMG-7775.png

Rotor is removed now on to the autowinding bridge. Here it's very important to just remove
the 3 silver screws marked with green rings in picture. The other black screws are just glued deco screws.

IMG-7776.png

So here are the deco screws. Do not touch them! Also the jewels marked with orange are just decoration so do not put any oil here after the movement is cleaned.

IMG-7777.png

here is the rotor and bridge in the part tray.

IMG-7778.png

Here we now see the real autowinding bridge with the real jewels and hidden screws
but we leave them for now and remove the movement from the case. Movement screws and tabs
are located by the red arrows, all of them were pretty lose but I'm afraid to tighten them
enough (to Swiss Standard) because if they break it will be trouble find replacement and they
probably get stuck in the mainplate for ever.

IMG-7779.png

Movement is out, now carfully remove the hands.


IMG-7780.png

When the hands is removed and put away in saftey turn the dial feet screws about 180 degrees, marked in the red circles and carfylly remove the dial.
The DW is right under the dial so don't push the edge with a sharp screw driver or something like that.
When dial is disassembled you can take away the black movement ring, it's sitting quite tight.

IMG-7781.png

With the dial removed next is the front of the movement. There are 3 black screws they are all quite delicate so be careful not tighten them too hard when putting movement back together.

IMG-7783.png

With the first plate removed we now have the DW lose, just be carefull as the date jumper and jumper spring are under tension and easy fly away.
At the point where the red line touch the jumper it need to be properly oiled to get a smooth date change.
I use HP 1300 or Microgliss D5.


IMG-7784.png

The foil washer on the hour wheel was sad (red) it usualy should be happy so I will put it back as the green line in the picture shows.

IMG-7785.png

Then I remove the top part of the hour wheel, under it there are the mechanism to jump the hours for date setting it have to be greased and not oiled Moebuis 9504 (synt-a-alube) is the best option. The grease spot is shown by
the red arrow. The gears do not engage (yellow/green lines) as the date jumper finger only engages with the top gear of the hour wheel this is to forward the date when jumping the hours around in date set mode.
Then unscrew the 3 screws on the calender plate.


IMG-7786.png

The calender plate where the DW turn. The area where the DW turn is quite big I may try to modify this to decrease the friction.

IMG-7787.png

The underside of the calendar plate where the two gears are riveted and can't be removed so they need to be oiled after cleaning. Put small amounts of HP1300 where the thinn green arrows point.

IMG-7788.png

The keyless is a modifyed A7750 and most parts there are a direct swap. Also now the date finger gear and the transport gear can be removed.


IMG-7789.png

The small bridge and the wheels are next to be removed.

IMG-7790.png

The pillar (red arrow) did not have proper oiling and it have some wear on mine so I will lathe a new one and press in to the mainplate.
The oil is however there in the wrong place (yellow arrow) and I think it's chinese motor oil. The oil is sticky and make the movement worse than if it was dry.
The green arrow shows some dirt where the hourwheel turns over the minute wheel. It will probably all turn much smoother after cleaning and oiling.

IMG-7791.png

Back to the backside of the movement agail. Now it's time to look at the actual autowinding bridge.
the lime green circles around jewels are the actual jewels but the one marked with orange ist just for show,
it's placed directly under one of the jewels in the deco plate. just to make a more autentic look I think.

Don't remove the autowinding bridge yet I start with the balance bridge.
It's actually easier than on a gen 8500 as it have the normal swiss lever escapement so lift it straight up but gentle.

IMG-7792.png

Next remove all mainspring power from the barrels by holding the crown and then push this lever all the way up.
this will make the crown turn so let it slip gently between your fingers until the power is gone from movement.


IMG-7793.png

When there is no power in the geartrain its safe to remove the palletfork bridge with the 2 screws (green)

Do not try to remove the deco balancewheel protection. it seems to be glued and you risk to break the screw head. (Red X circle)


IMG-7794.png

Now it's finally time for the autowinding bridge.

IMG-7795.png

here we have 2 A2824-2 reversing wheels and then 2 custom wheels.


IMG-7796.png

Autowinding wheels gone now the geartrain bridge hold by two black screws.


IMG-7797.png

Before removing gears I remove the Barrel bridge.


IMG-7798.png

Underside of barrel bridge where the ratchet for the barrels are located
everything here except the riveted wheel (red arrow) can be removed and cleaned before oiling (HP1300)


IMG-7799.png

The two barrels but be carefull as they look to be the same but they aren't. It seems like one of them have no clutch system so if they are mixed up the autowinding can possibly overwind and break the mainspring or gears. I'll just be on the safe side and mark them with 1 and 2 small x-marks where it can't be seen.
The yellow arrow is the balance stop it had more of the chinese motor oil under it. Yuck!!!


IMG-7800.png

Back on the front for the last dissasembly of the keyless. Here its the same as for any A7750.


IMG-7801.png

Some of the parts was little bent so they will be replaced with new A7750 parts.


IMG-7802.png

Winding stem is pretty much a normal 7750 made to be able to push it back without pusing the stem lever.
(a small angle after the square part of the stem)
there are probably A7750 stems like this in a bunch of other reps too.


IMG-7803.png

Empty mailplate.


IMG-7804.jpg

Ready to be put in cleaning baskets. As the movment text isn't engraved and just printed on yo the bridges,
except the rotor I will only clean it on a short program of 5 min in cleaning alcohol ISO propanol. then quick heat dry it for 3-4 min.



I'm abit tierd after all the documentation so I will see when I have time for a update on this but until then take care and let me know if there are any questionmarks.

Cheers
Santre
I wanted to compliment you on this post. I have the same watch, unfortunately after 4 years the movement stopped, perhaps broken. I wanted to know if there are spare parts for this clone. If the 8500 movement is not repairable, can it be replaced with a 2824 movement? Does the watch case support it? are the dimensions the same? Thanks for the reply
 

Ema79

You're Saying I Can Sell?
25/12/18
95
5
8
Can anyone tell me if on my “Omega Planet Ocean” I can replace the movement super clone 8500 with an Asian 2824 ?
Thanks
 

OnTheSly

You're Saying I Can Sell?
24/6/23
49
46
18
Best Coast
Can anyone tell me if on my “Omega Planet Ocean” I can replace the movement super clone 8500 with an Asian 2824 ?
Thanks
No, the 2824 isn't a straight swap with the 8500. It has some parts from the 2824 but also has some custom parts.
 

Ema79

You're Saying I Can Sell?
25/12/18
95
5
8
No, the 2824 isn't a straight swap with the 8500. It has some parts from the 2824 but also has some custom parts.
yes ! this is clear for me. Maybe I didn't explain myself very well. If I don't find (through TD) a complete 8500 movement to replace the broken one, can I mount a movement complete 2824 on my Planet Ocean VSF?
Thanks